Digiprog 3 4.94 User Manual

Digiprog 3 4.94 User Manual

OBD2Tuning.com: FAQ - Automotive Diagnostic Tools Auto Key Programmer Auto ECU Repair Tool Chip Socket and Programmer OBD2 Diagnostic Interface ECU Chip Tuning Immobilizer Immo Emulator Odometer Correction Tool Car Key Chips OBD2Tuning VIP Order Auto Repair Manual Software Heavy Duty Truck Diagnostic Car Accessories Repair,DSLR Camera Accessories. Aug 03, 2015 - sorted list of cars which should directly work on OBD with digiprog 4.94 - UPDATE: instructions how to open odometer and change mileage peugeot 108 / Aygo 2016 (same password) And for those who don't have it already: - official german manuals (manuals are old but they often do have better pictures) - updates for 4.94 (20 serials).

Here is the detail instruction on how to program EEPROM with digiprog 3 odometer correction tool through “EEPROM” menu.

EEPROM programming with Digiprog 3 is done through some adapters, for example, 01/04 Adapter,Digiprog 3 ST02 cable or others. These adapters can be purchased at local aftermarket shops or from online stores.

EEPROM chip 01/04 Adapter picture taken:

Tips before you start:
1. De-solder eeprom
2. Make sure the contact points or legs with glass fiber pin thoroughly.
3. Clean clearly with sandpaper, etc
4. Insert eeprom correctly into Digiprog3 ST01/ST04 adapter, and make sure they are contacting.

How to program EEPROM using digiprog 3 mileage correction tool?
1. Connect DP3 device to your car via OBD connector
2. Enter “EEPROM” menu
3. Read data from EEPROM and store them in digiprog3
Follow this way:
Select the “SET TYPE” and choose “93C46″, then your digiprog has been set up to read a 93C46 chip. Press “EEPROM” again and then “READ”. There will show you the information on the digiprog III screen when the reading is complete. Now press “VERIFY” so the information on your screen can agree with the Eeprom.
Next click the “FILE” and there will show you another sub-menu, you can click “SAVE” and enter a file name for the information you are saving. Once you entered the file name, your data is safe and the vehicle is now ready to be reprogrammed.

4. Get EEPROM from ST01/ST04 adapter and reload it;
5. Select the function EEPROM COMPARE;
6. Then it is the previous read data on digiprog 3 but not the internal memory, comparing it with the now re-inserted EEPROM;

NOTE:
Error message may appear during the process, restore or reprogram, restore the original data status and it will be fixed.

External eeprom programmer

Read and store data status
Take EEPROM from the adapter and insert it again
Re-read data level and save it
Comparison on data sets in the editor (windows—total commander)
If the comparison is identical, it is correct.
If the data is restored already, the reprogramming error shows the original data
Data state produced!

Case: Digiprog3 read&write Audi A4 eeprom HC12 mileage

Purpose:

copy the immo information from a cluster to another
make the mileage follow with the immo information

Model:

Audi a4 2001

Optional devices:

Digiprog3, or ecu programmers like Xprog, Carprog, UPA-USB programmer

Original cluster:

The Jaeger cluster barely works

Suggestion:

read the pin code from both the Instrument and adapt it to the vehicle

What to do on pin 21 and 22 on the chip:

– With ECU programmers:

Eprom.set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.
Buy yourself Xprog-M, Carprog, UPA-USB.
Pin 21 and 22 jumper after programming or wait 10 minutes.

– with Digiprog3:

Eprom,set type,mcu,hc12,read,save.
eprom,set type,mcu,hc12,file,load,write.

Problem & Solution: Digiprog3 Can’t Read EEPROM

Problem:

Used OBD ST01 & ST04 cables (contained in Digiprog 3 entire kit)to read EEPROM. The pic below shows what I did.

But the result can be seen like the following pic. The EEPROM cannot be read.

Digiprog 3 4.94 user manual free

Solution:

  1. Take down the clip and clear the chip. Then try it again.
  2. If you do not want the clip,contact the purchasing specialist to ask for the 01/04 Adapter for Digiprog 3.

Disconnect digiprog 3 from your car when finished.

Related posts:

In this blog uobdii.com will offer you Digiprog 3 V4.94 Update Service and show you how to install Digiprog iii V4.94 software step by step! If you have DP3 clone V4.88 or lower version, check below:

Get V4.94 Digiprog iii update software service here:

For Serial Number 590C8F0E0000 24CC65070000 and AFD68C070000 check below:

Note: Waterworld movie torrent download.

  1. Do not update the Digiprog 3 online when you use;
  2. Disable any anti-virus software on your computer before running an update;
  3. Make sure your computer will not become standby status when updating. Computer power must be well connected. Update will take 15-20 minutes;
  4. Please confirm the update file is complete as display below, or will cause blue screen.

How to install V4.94 Digiprog iii software?

Copy and paste Digiprog 3 patch and update video rar to desktop, then extract them and all files in both folders

Mount on desktop, right click “Properties”

Click “Power”

Set “Turn off monitor” to “Never”

Set “Turn off hard disk” to “Never”

Set “System Standby” to “Never”

Set “Wait” value to “9999” minute

Connect DP3 mileage correction tool with computer via USB cable

Wait the system to detect driver

Found new hardware wizard

Select “Install from a list of specific location (advanced)”, click “Next”

Browse file to C:/Document and Settings/Desktop/Digiprog3-4.94 update video/CDM 2.08.30 x86WHCL Certified

Click “Next”

Click “Finish” when driver is installed

Install hardware wizard

Select “Install from a list of specific location (advanced)”, click “Next”

Click “Next”

Click “Finish”

Open 81C62817000-v4.94patch folder on desktop

Open Digiloader1 then click “Select the port and click me” button

Then open My Computer>>Manager>>Device Manager>>Ports>> USB Serial Port (COM4) to check COM Port is set to COM4

Set COM port to “COM4” and filename “Digi1 bin”. Click on “Select the port and click me” button

Digiprog 3 4.94 User Manual Download

Message say Process end. Click “OK” to complete it.

Digiprog 3 Unknown Dashboard

Related posts:

Comments are closed.